22 files changed, 0 insertions, 622 deletions
diff --git a/tests/AnalogInOutSerial/AnalogInOutSerial.ino b/tests/AnalogInOutSerial/AnalogInOutSerial.ino
deleted file mode 100644
index e142f69..0000000
--- a/tests/AnalogInOutSerial/AnalogInOutSerial.ino
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
-  Analog input, analog output, serial output
- 
- Reads an analog input pin, maps the result to a range from 0 to 255
- and uses the result to set the pulsewidth modulation (PWM) of an output pin.
- Also prints the results to the serial monitor.
- 
- The circuit:
- * potentiometer connected to analog pin 0.
-   Center pin of the potentiometer goes to the analog pin.
-   side pins of the potentiometer go to +5V and ground
- * LED connected from digital pin 9 to ground
- 
- created 29 Dec. 2008
- modified 30 Aug 2011
- by Tom Igoe
- 
- This example code is in the public domain.
- 
- */
-
-// These constants won't change.  They're used to give names
-// to the pins used:
-const int analogInPin = A0;  // Analog input pin that the potentiometer is attached to
-const int analogOutPin = 9; // Analog output pin that the LED is attached to
-
-int sensorValue = 0;        // value read from the pot
-int outputValue = 0;        // value output to the PWM (analog out)
-
-void setup() {
-  // initialize serial communications at 9600 bps:
-  Serial.begin(9600); 
-}
-
-void loop() {
-  // read the analog in value:
-  sensorValue = analogRead(analogInPin);            
-  // map it to the range of the analog out:
-  outputValue = map(sensorValue, 0, 1023, 0, 255);  
-  // change the analog out value:
-  analogWrite(analogOutPin, outputValue);           
-
-  // print the results to the serial monitor:
-  Serial.print("sensor = " );                       
-  Serial.print(sensorValue);      
-  Serial.print("\t output = ");      
-  Serial.println(outputValue);   
-
-  // wait 10 milliseconds before the next loop
-  // for the analog-to-digital converter to settle
-  // after the last reading:
-  delay(10);                     
-}
diff --git a/tests/AnalogInOutSerial/Makefile b/tests/AnalogInOutSerial/Makefile
deleted file mode 100644
index 872d069..0000000
--- a/tests/AnalogInOutSerial/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-BOARD_TAG    = uno
-ARDUINO_LIBS =
-
-include ../TestSuiteCommon.mk
-include ../../Arduino.mk
diff --git a/tests/Blink/Blink.ino b/tests/Blink/Blink.ino
deleted file mode 100644
index 1953c39..0000000
--- a/tests/Blink/Blink.ino
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
-  Blink
-  Turns on an LED on for one second, then off for one second, repeatedly.
- 
-  This example code is in the public domain.
- */
-
-void setup() {                
-  // initialize the digital pin as an output.
-  // Pin 13 has an LED connected on most Arduino boards:
-  pinMode(13, OUTPUT);     
-}
-
-void loop() {
-  digitalWrite(13, HIGH);   // set the LED on
-  delay(1000);              // wait for a second
-  digitalWrite(13, LOW);    // set the LED off
-  delay(1000);              // wait for a second
-}
diff --git a/tests/Blink/Makefile b/tests/Blink/Makefile
deleted file mode 100644
index d41effa..0000000
--- a/tests/Blink/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-BOARD_TAG    = uno
-ARDUINO_LIBS =
-
-include ../TestSuiteCommon.mk
-include ../../Arduino.mk
-
diff --git a/tests/BlinkChipKIT/BlinkChipKIT.pde b/tests/BlinkChipKIT/BlinkChipKIT.pde
deleted file mode 100644
index 1953c39..0000000
--- a/tests/BlinkChipKIT/BlinkChipKIT.pde
+++ /dev/null
@@ -1,19 +0,0 @@
-/*
-  Blink
-  Turns on an LED on for one second, then off for one second, repeatedly.
- 
-  This example code is in the public domain.
- */
-
-void setup() {                
-  // initialize the digital pin as an output.
-  // Pin 13 has an LED connected on most Arduino boards:
-  pinMode(13, OUTPUT);     
-}
-
-void loop() {
-  digitalWrite(13, HIGH);   // set the LED on
-  delay(1000);              // wait for a second
-  digitalWrite(13, LOW);    // set the LED off
-  delay(1000);              // wait for a second
-}
diff --git a/tests/BlinkChipKIT/Makefile b/tests/BlinkChipKIT/Makefile
deleted file mode 100644
index bec2794..0000000
--- a/tests/BlinkChipKIT/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-BOARD_TAG    = mega_pic32
-ARDUINO_LIBS =
-
-include ../TestSuiteCommon.mk
-include ../../chipKIT.mk
-
diff --git a/tests/BlinkInAVRC/Makefile b/tests/BlinkInAVRC/Makefile
deleted file mode 100644
index 9080b24..0000000
--- a/tests/BlinkInAVRC/Makefile
+++ /dev/null
@@ -1,17 +0,0 @@
-# This sample Makefile, explains how you can compile plain AVR C file.
-#
-# Arduino Make file. Refer to https://github.com/sudar/Arduino-Makefile
-
-NO_CORE = Yes
-
-BOARD_TAG    = atmega16
-MCU = atmega16
-F_CPU = 8000000L
-
-ISP_PROG   = stk500v1
-AVRDUDE_ISP_BAUDRATE = 19200
-
-include ../TestSuiteCommon.mk
-include $(ARDMK_DIR)/Arduino.mk
-
-# !!! Important. You have to use make ispload to upload when using ISP programmer
diff --git a/tests/BlinkInAVRC/blink.c b/tests/BlinkInAVRC/blink.c
deleted file mode 100644
index d8b7c8f..0000000
--- a/tests/BlinkInAVRC/blink.c
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * � Anil Kumar Pugalia, 2010. Email: email@sarika-pugs.com
- *
- * ATmega48/88/168, ATmega16/32
- * 
- * Example Blink. Toggles all IO pins at 1Hz
- */
-
-#include <avr/io.h>
-#include <util/delay.h>
-
-void init_io(void)
-{
-	// 1 = output, 0 = input
-	DDRB = 0b11111111; // All outputs
-	DDRC = 0b11111111; // All outputs
-	DDRD = 0b11111110; // PORTD (RX on PD0). Just for demo
-}
-
-int main(void)
-{
-	init_io();
-
-	while (1)
-	{
-		PORTC = 0xFF;
-		PORTB = 0xFF;
-		PORTD = 0xFF;
-		_delay_ms(500);
-
-		PORTC = 0x00;
-		PORTB = 0x00;
-		PORTD = 0x00;
-		_delay_ms(500);
-	}
-
-	return 0;
-}
diff --git a/tests/BlinkWithoutDelay/BlinkWithoutDelay.ino b/tests/BlinkWithoutDelay/BlinkWithoutDelay.ino
deleted file mode 100644
index 0143571..0000000
--- a/tests/BlinkWithoutDelay/BlinkWithoutDelay.ino
+++ /dev/null
@@ -1,65 +0,0 @@
-/* Blink without Delay
- 
- Turns on and off a light emitting diode(LED) connected to a digital  
- pin, without using the delay() function.  This means that other code
- can run at the same time without being interrupted by the LED code.
- 
- The circuit:
- * LED attached from pin 13 to ground.
- * Note: on most Arduinos, there is already an LED on the board
- that's attached to pin 13, so no hardware is needed for this example.
- 
- 
- created 2005
- by David A. Mellis
- modified 8 Feb 2010
- by Paul Stoffregen
- 
- This example code is in the public domain.
-
- 
- http://www.arduino.cc/en/Tutorial/BlinkWithoutDelay
- */
-
-// constants won't change. Used here to 
-// set pin numbers:
-const int ledPin =  13;      // the number of the LED pin
-
-// Variables will change:
-int ledState = LOW;             // ledState used to set the LED
-long previousMillis = 0;        // will store last time LED was updated
-
-// the follow variables is a long because the time, measured in miliseconds,
-// will quickly become a bigger number than can be stored in an int.
-long interval = 1000;           // interval at which to blink (milliseconds)
-
-void setup() {
-  // set the digital pin as output:
-  pinMode(ledPin, OUTPUT);      
-}
-
-void loop()
-{
-  // here is where you'd put code that needs to be running all the time.
-
-  // check to see if it's time to blink the LED; that is, if the 
-  // difference between the current time and last time you blinked 
-  // the LED is bigger than the interval at which you want to 
-  // blink the LED.
-  unsigned long currentMillis = millis();
- 
-  if(currentMillis - previousMillis > interval) {
-    // save the last time you blinked the LED 
-    previousMillis = currentMillis;   
-
-    // if the LED is off turn it on and vice-versa:
-    if (ledState == LOW)
-      ledState = HIGH;
-    else
-      ledState = LOW;
-
-    // set the LED with the ledState of the variable:
-    digitalWrite(ledPin, ledState);
-  }
-}
-
diff --git a/tests/BlinkWithoutDelay/Makefile b/tests/BlinkWithoutDelay/Makefile
deleted file mode 100644
index 872d069..0000000
--- a/tests/BlinkWithoutDelay/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-BOARD_TAG    = uno
-ARDUINO_LIBS =
-
-include ../TestSuiteCommon.mk
-include ../../Arduino.mk
diff --git a/tests/Fade/Fade.ino b/tests/Fade/Fade.ino
deleted file mode 100644
index b47bf43..0000000
--- a/tests/Fade/Fade.ino
+++ /dev/null
@@ -1,31 +0,0 @@
-/*
- Fade
- 
- This example shows how to fade an LED on pin 9
- using the analogWrite() function.
- 
- This example code is in the public domain.
- 
- */
-int brightness = 0;    // how bright the LED is
-int fadeAmount = 5;    // how many points to fade the LED by
-
-void setup()  { 
-  // declare pin 9 to be an output:
-  pinMode(9, OUTPUT);
-} 
-
-void loop()  { 
-  // set the brightness of pin 9:
-  analogWrite(9, brightness);    
-
-  // change the brightness for next time through the loop:
-  brightness = brightness + fadeAmount;
-
-  // reverse the direction of the fading at the ends of the fade: 
-  if (brightness == 0 || brightness == 255) {
-    fadeAmount = -fadeAmount ; 
-  }     
-  // wait for 30 milliseconds to see the dimming effect    
-  delay(30);                            
-}
diff --git a/tests/Fade/Makefile b/tests/Fade/Makefile
deleted file mode 100644
index 872d069..0000000
--- a/tests/Fade/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-BOARD_TAG    = uno
-ARDUINO_LIBS =
-
-include ../TestSuiteCommon.mk
-include ../../Arduino.mk
diff --git a/tests/HelloWorld/HelloWorld.ino b/tests/HelloWorld/HelloWorld.ino
deleted file mode 100644
index e99957d..0000000
--- a/tests/HelloWorld/HelloWorld.ino
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
-  LiquidCrystal Library - Hello World
- 
- Demonstrates the use a 16x2 LCD display.  The LiquidCrystal
- library works with all LCD displays that are compatible with the 
- Hitachi HD44780 driver. There are many of them out there, and you
- can usually tell them by the 16-pin interface.
- 
- This sketch prints "Hello World!" to the LCD
- and shows the time.
- 
-  The circuit:
- * LCD RS pin to digital pin 12
- * LCD Enable pin to digital pin 11
- * LCD D4 pin to digital pin 5
- * LCD D5 pin to digital pin 4
- * LCD D6 pin to digital pin 3
- * LCD D7 pin to digital pin 2
- * LCD R/W pin to ground
- * 10K resistor:
- * ends to +5V and ground
- * wiper to LCD VO pin (pin 3)
- 
- Library originally added 18 Apr 2008
- by David A. Mellis
- library modified 5 Jul 2009
- by Limor Fried (http://www.ladyada.net)
- example added 9 Jul 2009
- by Tom Igoe
- modified 22 Nov 2010
- by Tom Igoe
- 
- This example code is in the public domain.
-
- http://www.arduino.cc/en/Tutorial/LiquidCrystal
- */
-
-// include the library code:
-#include <LiquidCrystal.h>
-
-// initialize the library with the numbers of the interface pins
-LiquidCrystal lcd(12, 11, 5, 4, 3, 2);
-
-void setup() {
-  // set up the LCD's number of columns and rows: 
-  lcd.begin(16, 2);
-  // Print a message to the LCD.
-  lcd.print("hello, world!");
-}
-
-void loop() {
-  // set the cursor to column 0, line 1
-  // (note: line 1 is the second row, since counting begins with 0):
-  lcd.setCursor(0, 1);
-  // print the number of seconds since reset:
-  lcd.print(millis()/1000);
-}
-
diff --git a/tests/HelloWorld/Makefile b/tests/HelloWorld/Makefile
deleted file mode 100644
index 0af2ed4..0000000
--- a/tests/HelloWorld/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-BOARD_TAG    = uno
-ARDUINO_LIBS = LiquidCrystal
-
-include ../TestSuiteCommon.mk
-include ../../Arduino.mk
diff --git a/tests/TestSuiteCommon.mk b/tests/TestSuiteCommon.mk
deleted file mode 100644
index 5fa4f50..0000000
--- a/tests/TestSuiteCommon.mk
+++ /dev/null
@@ -1,13 +0,0 @@
-ARDMK_DIR=../../
-DEPENDENCIES_FOLDER = ../../dependencies
-DEPENDENCIES_MPIDE_DIR = $(DEPENDENCIES_FOLDER)/mpide-0023-linux64-20130817-test
-
-ifeq ($(MPIDE_DIR),)
-	MPIDE_DIR = $(DEPENDENCIES_MPIDE_DIR)
-endif
-
-DEPENDENCIES_ARDUINO_DIR = $(DEPENDENCIES_FOLDER)/arduino-1.0.5
-
-ifeq ($(ARDUINO_DIR),)
-	ARDUINO_DIR = $(DEPENDENCIES_ARDUINO_DIR)
-endif
diff --git a/tests/WebServer/Makefile b/tests/WebServer/Makefile
deleted file mode 100644
index 5fbefae..0000000
--- a/tests/WebServer/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@
-# Arduino Make file. Refer to https://github.com/sudar/Arduino-Makefile
-
-BOARD_TAG    = uno
-ARDUINO_LIBS = Ethernet SPI
-
-include ../TestSuiteCommon.mk
-include ../../Arduino.mk
diff --git a/tests/WebServer/WebServer.ino b/tests/WebServer/WebServer.ino
deleted file mode 100644
index fb2a1b9..0000000
--- a/tests/WebServer/WebServer.ino
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
-  Web Server
- 
- A simple web server that shows the value of the analog input pins.
- using an Arduino Wiznet Ethernet shield. 
- 
- Circuit:
- * Ethernet shield attached to pins 10, 11, 12, 13
- * Analog inputs attached to pins A0 through A5 (optional)
- 
- created 18 Dec 2009
- by David A. Mellis
- modified 4 Sep 2010
- by Tom Igoe
- 
- */
-
-#include <SPI.h>
-#include <Ethernet.h>
-
-// Enter a MAC address and IP address for your controller below.
-// The IP address will be dependent on your local network:
-byte mac[] = { 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
-IPAddress ip(192,168,1, 178);
-
-// Initialize the Ethernet server library
-// with the IP address and port you want to use 
-// (port 80 is default for HTTP):
-EthernetServer server(80);
-
-void setup()
-{
-  // start the Ethernet connection and the server:
-  Ethernet.begin(mac, ip);
-  server.begin();
-}
-
-void loop()
-{
-  // listen for incoming clients
-  EthernetClient client = server.available();
-  if (client) {
-    // an http request ends with a blank line
-    boolean currentLineIsBlank = true;
-    while (client.connected()) {
-      if (client.available()) {
-        char c = client.read();
-        // if you've gotten to the end of the line (received a newline
-        // character) and the line is blank, the http request has ended,
-        // so you can send a reply
-        if (c == '\n' && currentLineIsBlank) {
-          // send a standard http response header
-          client.println("HTTP/1.1 200 OK");
-          client.println("Content-Type: text/html");
-          client.println();
-
-          // output the value of each analog input pin
-          for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
-            client.print("analog input ");
-            client.print(analogChannel);
-            client.print(" is ");
-            client.print(analogRead(analogChannel));
-            client.println("<br />");
-          }
-          break;
-        }
-        if (c == '\n') {
-          // you're starting a new line
-          currentLineIsBlank = true;
-        } 
-        else if (c != '\r') {
-          // you've gotten a character on the current line
-          currentLineIsBlank = false;
-        }
-      }
-    }
-    // give the web browser time to receive the data
-    delay(1);
-    // close the connection:
-    client.stop();
-  }
-}
diff --git a/tests/master_reader/Makefile b/tests/master_reader/Makefile
deleted file mode 100644
index 8a42a8e..0000000
--- a/tests/master_reader/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@
-# Arduino Make file. Refer to https://github.com/sudar/Arduino-Makefile
-
-BOARD_TAG    = uno
-ARDUINO_LIBS = Wire
-
-include ../TestSuiteCommon.mk
-include ../../Arduino.mk
diff --git a/tests/master_reader/master_reader.ino b/tests/master_reader/master_reader.ino
deleted file mode 100644
index 4124d7d..0000000
--- a/tests/master_reader/master_reader.ino
+++ /dev/null
@@ -1,32 +0,0 @@
-// Wire Master Reader
-// by Nicholas Zambetti <http://www.zambetti.com>
-
-// Demonstrates use of the Wire library
-// Reads data from an I2C/TWI slave device
-// Refer to the "Wire Slave Sender" example for use with this
-
-// Created 29 March 2006
-
-// This example code is in the public domain.
-
-
-#include <Wire.h>
-
-void setup()
-{
-  Wire.begin();        // join i2c bus (address optional for master)
-  Serial.begin(9600);  // start serial for output
-}
-
-void loop()
-{
-  Wire.requestFrom(2, 6);    // request 6 bytes from slave device #2
-
-  while(Wire.available())    // slave may send less than requested
-  { 
-    char c = Wire.read(); // receive a byte as character
-    Serial.print(c);         // print the character
-  }
-
-  delay(500);
-}
diff --git a/tests/toneMelody/Makefile b/tests/toneMelody/Makefile
deleted file mode 100644
index 872d069..0000000
--- a/tests/toneMelody/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-BOARD_TAG    = uno
-ARDUINO_LIBS =
-
-include ../TestSuiteCommon.mk
-include ../../Arduino.mk
diff --git a/tests/toneMelody/pitches.h b/tests/toneMelody/pitches.h
deleted file mode 100644
index 55c7d54..0000000
--- a/tests/toneMelody/pitches.h
+++ /dev/null
@@ -1,95 +0,0 @@
-/*************************************************
- * Public Constants
- *************************************************/
-
-#define NOTE_B0  31
-#define NOTE_C1  33
-#define NOTE_CS1 35
-#define NOTE_D1  37
-#define NOTE_DS1 39
-#define NOTE_E1  41
-#define NOTE_F1  44
-#define NOTE_FS1 46
-#define NOTE_G1  49
-#define NOTE_GS1 52
-#define NOTE_A1  55
-#define NOTE_AS1 58
-#define NOTE_B1  62
-#define NOTE_C2  65
-#define NOTE_CS2 69
-#define NOTE_D2  73
-#define NOTE_DS2 78
-#define NOTE_E2  82
-#define NOTE_F2  87
-#define NOTE_FS2 93
-#define NOTE_G2  98
-#define NOTE_GS2 104
-#define NOTE_A2  110
-#define NOTE_AS2 117
-#define NOTE_B2  123
-#define NOTE_C3  131
-#define NOTE_CS3 139
-#define NOTE_D3  147
-#define NOTE_DS3 156
-#define NOTE_E3  165
-#define NOTE_F3  175
-#define NOTE_FS3 185
-#define NOTE_G3  196
-#define NOTE_GS3 208
-#define NOTE_A3  220
-#define NOTE_AS3 233
-#define NOTE_B3  247
-#define NOTE_C4  262
-#define NOTE_CS4 277
-#define NOTE_D4  294
-#define NOTE_DS4 311
-#define NOTE_E4  330
-#define NOTE_F4  349
-#define NOTE_FS4 370
-#define NOTE_G4  392
-#define NOTE_GS4 415
-#define NOTE_A4  440
-#define NOTE_AS4 466
-#define NOTE_B4  494
-#define NOTE_C5  523
-#define NOTE_CS5 554
-#define NOTE_D5  587
-#define NOTE_DS5 622
-#define NOTE_E5  659
-#define NOTE_F5  698
-#define NOTE_FS5 740
-#define NOTE_G5  784
-#define NOTE_GS5 831
-#define NOTE_A5  880
-#define NOTE_AS5 932
-#define NOTE_B5  988
-#define NOTE_C6  1047
-#define NOTE_CS6 1109
-#define NOTE_D6  1175
-#define NOTE_DS6 1245
-#define NOTE_E6  1319
-#define NOTE_F6  1397
-#define NOTE_FS6 1480
-#define NOTE_G6  1568
-#define NOTE_GS6 1661
-#define NOTE_A6  1760
-#define NOTE_AS6 1865
-#define NOTE_B6  1976
-#define NOTE_C7  2093
-#define NOTE_CS7 2217
-#define NOTE_D7  2349
-#define NOTE_DS7 2489
-#define NOTE_E7  2637
-#define NOTE_F7  2794
-#define NOTE_FS7 2960
-#define NOTE_G7  3136
-#define NOTE_GS7 3322
-#define NOTE_A7  3520
-#define NOTE_AS7 3729
-#define NOTE_B7  3951
-#define NOTE_C8  4186
-#define NOTE_CS8 4435
-#define NOTE_D8  4699
-#define NOTE_DS8 4978
-
-
diff --git a/tests/toneMelody/toneMelody.ino b/tests/toneMelody/toneMelody.ino
deleted file mode 100644
index 8593ab7..0000000
--- a/tests/toneMelody/toneMelody.ino
+++ /dev/null
@@ -1,49 +0,0 @@
-/*
-  Melody
- 
- Plays a melody 
- 
- circuit:
- * 8-ohm speaker on digital pin 8
- 
- created 21 Jan 2010
- modified 30 Aug 2011
- by Tom Igoe 
-
-This example code is in the public domain.
- 
- http://arduino.cc/en/Tutorial/Tone
- 
- */
- #include "pitches.h"
-
-// notes in the melody:
-int melody[] = {
-  NOTE_C4, NOTE_G3,NOTE_G3, NOTE_A3, NOTE_G3,0, NOTE_B3, NOTE_C4};
-
-// note durations: 4 = quarter note, 8 = eighth note, etc.:
-int noteDurations[] = {
-  4, 8, 8, 4,4,4,4,4 };
-
-void setup() {
-  // iterate over the notes of the melody:
-  for (int thisNote = 0; thisNote < 8; thisNote++) {
-
-    // to calculate the note duration, take one second 
-    // divided by the note type.
-    //e.g. quarter note = 1000 / 4, eighth note = 1000/8, etc.
-    int noteDuration = 1000/noteDurations[thisNote];
-    tone(8, melody[thisNote],noteDuration);
-
-    // to distinguish the notes, set a minimum time between them.
-    // the note's duration + 30% seems to work well:
-    int pauseBetweenNotes = noteDuration * 1.30;
-    delay(pauseBetweenNotes);
-    // stop the tone playing:
-    noTone(8);
-  }
-}
-
-void loop() {
-  // no need to repeat the melody.
-}